6.1. Power supply system and fuel injection
General information and security measures
Fuel tankFunction chart of system of microprocessor management of ME SFI 2.0. V6 and V8 engines
Arrangement of some electric elements
Air streams of the inlet pipeline with changeable geometry
Management of gas distribution. V6 and V8 engines
|
|
12 — the Inlet pipeline |
22 — the Resonant gate |
Elements of the inlet pipeline with changeable geometry
|
Assembly of the fuel pump (under the bottom, at the left behind) |
|
Fuel injectors (lateral faces of the engine) |
|
Pressure sensor in the fuel tank (a forward central part of a luggage carrier) |
|
Fuel reserve sensor (forward central part of a luggage carrier) |
|
Thermometric measuring instrument of mass of vsasyayemy air (central back part of the engine) |
|
Accelerator pedal sensor |
|
Sensor of position of the crankshaft |
|
Sensor of temperature of cooling liquid (forward, central part of the engine) |
|
Detonation sensors |
|
Right dokataliticheskiya lambda probe |
|
Left dokataliticheskiya lambda probe |
|
Left post-catalytic lambda probe |
|
Right post-catalytic lambda probe |
|
Element of installation of a butterfly valve (central back part of the engine) |
|
Injector of injection of fuel in the 1st cylinder (the right side of the engine) |
Petrol engines
Are a part of fuel system: established in a back part of the car (under a pillow of a back seat) the fuel tank with an adsorber on absorbent carbon, fuel-supply lines, the electric fuel pump, and also the electronic system of consecutive injection operated by the control unit. The function chart of a control system and an arrangement of sensors are submitted on accompanying illustrations.
The reserve of fuel is shown to the driver on the dashboard. Gather on the petrol engine of couple of gasoline in an adsorber and move in engine combustion chambers.
Style of driving of the car has significant effect on fuel consumption. Councils for decrease in fuel consumption:
- After start of the engine at once start even if it occurs on a frost.
- At a car stop for a while more on 40 with, switch off the engine.
- Move always on the highest transfer.
- At the movement on long distances whenever possible support uniform speed. Avoid the movement at high speeds. Drive the car circumspectly. Without need you do not brake.
- You transport the car excessive freight. If the luggage carrier is not used, remove it from a roof.
- Check air pressure in tires. Do not allow excessive pressure decrease.
Diesel engines
Are a part of fuel system: established in a back part of the car (under a pillow of a back seat) the fuel tank, the fuel filter, nozzles, fuel tubes and hoses, the fuel reserve sensor located in a tank and the block of electronic control the engine.Fuel moves the special pump via the filter. In the filter the dirt and water which is contained in fuel accumulates.
The engine is operated the electronic system similar to a control system of petrol engines. The system operates operation of the engine, analyzing information arriving from a large number of sensors.
On diesel models there is no accelerator cable. Instead of it on a pedal the sensor of its situation is installed.
The fuel cut-off valve at switching off of ignition is absent. To kill the engine at switching off of ignition, the control unit of the engine sends a signal which, in turn, stops supply of fuel to nozzles to the TNVD control unit.
Components of the fuel tank are not removed. The fuel system is designed so that not to allow air "suction" in the absence of fuel in a tank. The control unit constantly checks fuel level in a tank, processing information arriving from the sensor of a reserve of the fuel located in a tank. When falling a reserve of fuel to a certain level the control unit lights the warning lamp on the control panel then forcibly causes admissions of supply of fuel, limiting to that the maximum speed. It proceeds until fuel level in a tank does not exceed an admissible mark.
The fuel system of diesel engines is very reliable. When using pure fuel and performing regular service it has to function regularly before the termination of service life of the car. After very big run internal components of nozzles can wear out, and they will need to be repaired. As the pump - nozzles have a difficult design, repair is recommended to be carried out in a specialized workshop.
The fuel pump takes away fuel (D) of the lower point of the damper (55/4) serving for prevention of hit to the inlet highway of the pump of air during commission of turns with the low level of fuel in a tank (75).
The submersible fuel pump (M3/1) is run by the electronic module tracing quality of filling of a damper and provides an expense of 220 l/h at effective a napoyer of 0.3 atm.
In addition pumping of fuel in a damper is carried out by the auxiliary soaking-up pump working at the expense of a stream of the excess fuel returned in a tank from pressure regulator (5.0 atm.).
The components placed in a tank (including the fuel pump) are not subject to removal and recovery repair and in case of their refusal all tank assembled is subject to replacement. The exception makes only the sensor of a reserve of fuel (B4).
The throttle (55/3a) cuts fuel consumption in the pumping of the returnable line (A) brought to the pump to 50 l/h with a pressure of 5.0 atm. The regulator of pressure prevents increase of a pressure over 5.3 atm.
Security measures and rules of respect for purity during the work with fuel system
During the work with fuel system it is necessary to observe the following security measures and purity:
The remark on security measures
Do not use naked flame near a workplace, you do not smoke and you do not hold any strongly warmed objects. There is a danger of accident! You keep in readiness the fire extinguisher.
You monitor normal ventilation of a workplace. Fuel vapors are poisonous.
The fuel system is under pressure. When opening system fuel can escape under pressure. Collect fuel by a rag. Use goggles.
During the work with components of a power supply system of the diesel engine observe special precautionary measures. In special degree it belongs to nozzles. Keep in mind that fuel pressure at an exit makes about 1100 atmospheres of nozzles. Do not allow hit of any parts of a body under a fuel stream.
Hose connections fasten by means of tape or tightening collars. Tightening collars need to be replaced with tape collars or collars of the last design surely. For installation of tape collars there is special adaptation, for example HAZET 796-5.
Carefully clear connections and the places adjoining to them before opening.
Stack the removed details on a pure lining and close. Apply for this purpose polyethylene or paper. Do not apply for this purpose fibrous fabric!
Carefully close open details or put technological caps if repair lasts some time.
Establish into place only pure details. Take out spare parts from packing only just before installation. Do not apply details which were stored unpacked (for example, stored in a toolbox).
At open fuel system whenever possible do not work with compressed air. Whenever possible do not move at the same time the car.
Do not apply the sealants containing silicone. The silicone elements which got to the engine in the engine do not burn down and damage the oxygen sensor.
Security measures at removal of the fuel tank:
- Before removal of a tank merge from it fuel or pump out fuel the pump which is specially provided for this purpose.
- The fuel tank is removed from the lower party of the car. Before a detachment of collars of fastening of a tank bring to it from below a jack and linings.
- The empty tank is explosive and cannot be utilized in such look. Before utilization the tank has to be cut on a part. You watch that at the same time there was no spark. For this purpose hand over the fuel tank in the specialized enterprise.
- After installation of a tank into place start the engine and check tightness of all connections.